STAINLESS STEEL BESPOKE BRAIDED FLEXIBLE HOSE ASSEMBLIES
Part Number:
Bespoke Metal Hoses
DESIGN & MATERIAL CONSTRUCTION
Hose
Stainless Steel 316L
Braid
Stainless Steel AISI 304/304L
Temp
-269°C - +600°C
Sizes
¼” NB – 16” NB
DESCRIPTION
HydraFlex Bespoke Stainless-Steel hoses are manufactured in accordance with ISO 10380 : 2012. HydraFlex Hose assemblies are available as unbraided, covered with single stainless steel external wire braid or with double braid for increased working pressure. Hydraflex also offer our range of A200 & A700 Heavy-Duty Stainless-Steel
Hose Series which is designed for more arduous installations and higher working pressure applications. Typical stock range of end fittings available, in various materials such as Carbon Steel & Stainless Steel (Other materials available).
- BSPT / NPT Hex Fixed Male Connections
- BSPT / NPT Weld Nipple Connections
- BSP Cone Seat Swivel Unions (60 Degree)
- BSP Full Male Union (Cone Seat Swivel Unions (60 Degree) with Male / Male
adaptors) - (Various thread options available from stock).
- BSP Full Female Union (Cone Seat Swivel Unions (60 Degree) with Male / Female
adaptors) - (Various thread options available from stock).
- BSPT / NPT Fixed Female Connections
- Flanged Connections (Fixed) - Typically PN16 / ASA 150lb (Others available from
stock)
- Flanged Connections (Swivel) - Typically PN16 / ASA 150lb (Others available from
stock)
- Tube End Connections (Offered as Stock OD sizes with gauge or Schedule wall
thicknesses)
- Victaulic Grooved connections
All end fittings listed above can be supplied on 45 Degree (135) or 90 Degree
Configuration - Contact our Sales Office for more information.
APPLICATIONS
- Building Services
- HVAC-R Piping Lines
- Pump Connections,
- Vibration Producing Systems
- Industrial Process &Applications
- Steam connections
- Chemical Process
- Gas Connections
- Ultra-High Vacuum applications
- Exhaust systems
QUALITY & ASSOCIATED STANDARDS
All Hydraflex Metal Hoses are produced by fully penetrated TIG welding method to Hydraflex’s approved Weld procedures. Each and every Unit manufactured is 100% pressure tested to a minimum hydrostatic pressure test of 1.5 times of the design pressure. PED 2014/68/EU approval and material certificates to EN 10204 is available for all sizes.
- Absorption of Heat Expansion
- Absorption of Angular Movements
- Compensation of Parallel Pipeline Set Off
- Absorption of Oscillations
- Installation involving High and Low temperatures
- Vibration Elimination
TYPE 100 - STANDARD PITCH
TYPE 200 - STANDARD PITCH
TYPE 700 – HEAVY DUTY HOSE
TEMPERATURE / PRESSURE CORRECTION
REDUCTION COEFFICIENT OF PRESSURE AS A FUNCTION OF TEMPERATURE
END FITTINGS – HALF SECTION
PRESSURE DROP
The Pressure loss in corrugated hose is 100% higher than in new welded steel pipes. This means that in the case of corrugated hose an increase in diameter of approximately 15% is required to reduce the pressure loss to the
value of pressure loss in steel pipes. To utilise the chart...
- Identify the flow rate required on the base line (Horizontal Axis).
- Where the vertical line, that references to the nominal bore of the hose, intersects a horizontal line - Establish the pressure drop on the Vertical Axis. (Any data provided is for reference only. Please contact our Sales Team for additional information if required)
FLEXING INSTALLATIONS CHART
INSTALLATION GUIDE- DO’S & DON’T’S
LENGTH MEASURE POINTS
FURTHER INFORMATION
For any more information that you may require then please contact one of our team.
Northampton: 01604621964 Bolton: 01204529536 Rugby: 01604621964
Email: [email protected]
